General • Re: fetch error since 7.13: "failure: ERROR parsing http:...
Hi, I have thoroughly investigated this error, and it is due to an incorrect response from the server.The header contains the Content-Type field but does NOT contain the Content-Length field, and this...
View ArticleGeneral • CCR2216 All Interfaces on Switch Chip Flapping
Hello folks, we are observing a condition that shows as all interfaces simply flapping physical link state. The only physical interface not affected is ether1 which we know is direct to the CPU. See...
View ArticleGeneral • Re: CCR2216 All Interfaces on Switch Chip Flapping
Also will note that there are populated with DAC cables and RJ45 SFPs.Statistics: Posted by Archous — Fri Jan 10, 2025 12:34 pm
View ArticleGeneral • L2TP VPN not working after change to CCR2116 and ROS7.17rc6
With ROS 7.17rc6 i can't connect L2TP with PSK to MikroTik router CCR2116-12G-4S+.I can connect to other MT routers with that verion, but NOT to CCR2116 with VLAN interfaces(see attached...
View ArticleGeneral • Re: Question on massive site-to-site VPN implementation
the way, I solved the RoMON issue with ZeroTier: I had to enable bridging mode for each peer.This is when using /zerotier/controller for your peers? ...or using my.zerotier.com service?I ask since the...
View ArticleForwarding Protocols • eBGP dual-home
I am not very familiar with BGP filters and would like to understand if this type of implementation is possible.Then if there is some competent person who gives me some advice, all the better.I have a...
View ArticleWireless Networking • Re: New CapsMan Finally working with VLANS. Did I do it...
I used my own configs I'd created based upon what I'd read, and it didn't work. I referenced your post, and found I was missing these datapath statementsCode: /interface/wifi/datapath/add name=Corp_DP...
View ArticleBeginner Basics • Re: WiFi Station to Ethernet Port
I don't understand.The mAP lite has only one ethernet port, ether1.You want to connect your radio (wlan1) to an existing wi-fi network?Then the device is a "client" or "station" (and not an AP).And -...
View ArticleRouterBOARD hardware • Re: HEX S sometimes fails to start properly
Trying an alternate power supply won't be difficult anyway, the hex S accepts a wide range: DC jack input Voltage 12-57 V but also AC3 is pretty much flexible:DC jack input Voltage 12-28 V Personally...
View ArticleClik here to view.
General • Re: MLAG - client device with only one active link
After setting the lacp-rate to slow, everything works fine. I tried this with several other devices, fast (1s) would never work, it has to be slow (30s). The documentation doesn't mention this,...
View ArticleGeneral • Issue migrating from RB750Gr3 to rb5009ug_s_in, LAN can't access...
Hello,I'm migrating from a RB750Gr3 router to rb5009ug_s_in. I've exported the configuration from one device and imported it in the new one and I can see that the router is able to connect to...
View ArticleGeneral • Traffic generator strange problem
I am trying to setup a traffic generator and have a Router as a default gateway for the mikrotik device.The mikrotik device can ping the router ip address without any issues.However, when I am trying...
View ArticleGeneral • Re: Failover
In the case of Primary WAN1 and Secondary or Backup WAN2: In this case all traffic exits the router via WAN1 and one thinks primarily of LAN traffic. However, any external originated traffic arriving...
View ArticleGeneral • Re: Issue migrating from RB750Gr3 to rb5009ug_s_in, LAN can't...
Your configuration is a bit confusing to me.The only action=masquerade rule in the srcnat chain of /ip firewall nat matches on out-interface-list=WAN, and the only member of interface list WAN is...
View ArticleGeneral • Re: VLAN Trunk port config
1. Ensure that VLAN 10 and VLAN 20 are configured identically (tagged) on both the router (RB4011iGS+) and the main switch (CRS328-24P-4S+). Check VLAN IDs, tagging modes, and port configurations to...
View ArticleGeneral • Re: Wireguard peer sets a default ListeningPort=51820
The reason MikroTik's WireGuard peer generator automatically sets the `ListenPort = 51820` in the configuration is likely to align with the default port used by the WireGuard protocol. WireGuard...
View ArticleGeneral • Re: Throughput issues with PPPoE over 10Gbit XGS-PON
The bottleneck is likely due to the PPPoE process being CPU-intensive, especially at multi-gigabit speeds. The CCR2116, while powerful, may still struggle with PPPoE at such high throughputs due to...
View ArticleRouterOS beta • Re: /ip/route/check command disappeared?
So I went down the rabbit hole on how to do this without the "/ip route check" command. # something like this gets you the immediate-gw of the last route in the list, which is hopefully the most...
View ArticleGeneral • Mikrotik SMB Share - Veeam Backup Error
Hi,has anyone else tried useing SMB Share on Mikrotik with Veeam Backup Agent 6.x (currently using latest 6.3).I tried it on Mikrotik hAP-AX3 and ROS 7.15.x til ROS 7.16.1.Share is on USB (Nvme disk)....
View ArticleGeneral • PoE-out with Mode A
Hi folks,is there any MikroTik device which supports PoE-out with Mode A?I know the wiki (https://help.mikrotik.com/docs/spaces/R ... 69/PoE-Out) says "no" but I'm hardly searching a solution for...
View Article