Wireless Networking • RB2011 with a router switch and hap ax2 as aps
Hi, I'm at a friend's house trying to setup his hap ax2 units as aps (6 of them). The setup he has now is rb2011 with a router switch configured as a switch only and the aps to be connected to it. I'm...
View ArticleGeneral • Re: Problems with traffic flow through IPsec tunnel
Hi Alex and welcome to the forum!From your description, it sounds like you're running ROS v7 on a Mikrotik HeX (RB750Gr3) on the local side, but just to confirm, is the remote side a Bintec RS353? If...
View ArticleMikroTik hardware questions • upgrading old mikrotik RB2011UiAS-Rm
Hi everyone,just started to support a small company with RB2011UiAS-Rm as main router and the problem is - very slow internet speed. I am not very experinced with mikrotik, but what i've seen so far...
View ArticleAnnouncements • Re: v7.18.2 [stable] is released!
btw this config is wrong:Code: set [ find default-name=wifi2 ] configuration=cfg1 configuration.manager=capsman-or-local .mode=ap/interface wifi capset caps-man-addresses=127.0.0.1 certificate=request...
View ArticleMikroTik hardware questions • Re: upgrading old mikrotik RB2011UiAS-Rm
RB2011UiAS-Rm is a very old router that can route at around 250Mbps with moderately complex configuration. Your description of config makes it pretty complex so performance is likely even lower. And...
View ArticleGeneral • Email test failed when through proxy
I'm routing SMTP through a proxy in a container.I can confirm email is sent when not routed through proxy.But when i route through proxy, i see the following logs which are sent in sequence, after 30s...
View ArticleGeneral • Re: MPLS/VPLS decapsulation locked to single CPU core on ARM/ARM64...
Just like the CCR1036, the CCR2216 prefers one interface from the bond to transmit the encapsulated VPLS traffic because RouterOS cannot balance it with LACP and the supported hashing...
View ArticleMikroTik hardware questions • Re: Replacing a flash drive - problem with the...
One more question - after replacing the flash (and copying all the data from the old flash) were the MAC addresses (of ethernet and wifi interfaces) and device model and serial number (visible in...
View ArticleGeneral • Re: Email test failed when through proxy
Locally running this cURL command proxied through the same container, works fine:Code: curl --ssl smtp://smtp.mymail.com:587 --mail-from id@mymail.com --mail-rcpt test@myrcpt.com --upload-file...
View ArticleForwarding Protocols • Re: BGP Ignores Routing Table Despite Active 'A' Route
Can you post the output for the following following commands using the specific destination "ip address" your 2216 is forwarding to the wrong nexthop?/routing route print where "ip address" in...
View ArticleBeginner Basics • Re: Returning Newbie :) - Optimizing Bandwidth Config
No responses?? BummerStatistics: Posted by tdampier — Sat Mar 29, 2025 1:24 am
View ArticleGeneral • upgrade from V6 to V7 question for ccr1036
HiI wanted to upgrade my CCR1036-8G-2S+ to V7. Notice the should have 64G memory, but also read that it works on the the tiles.I went ahead any way, I am using this to get my config upgraded to V7 so...
View ArticleBeginner Basics • VoIP and Double NAT
HiMy Router Rb730 are planed to be used as Internet fail over between 2 ISP that provides me with their router and a cable to conect to my Mikrotik,the Question: how do i get my VoIP phone connected...
View ArticleGeneral • Re: upgrade from V6 to V7 question for ccr1036
I think Recent versions of Ros V7 don't have the upgrade from V6 conversion functionality any more.If you upgrade in the Gui from a very recent V6 to V7, it should offer you one of the V7.12.x...
View ArticleGeneral • Re: Upgrading CAPsMAN from 7.12.1 to 7.18.2
Stats are only available on the CAP itself, not on the CAPsMAN.Can you tell me where in CAP I can find it? I've looked everywhere and can't see it.If you are referring to WIFI ->WIFI (tab). No it...
View ArticleClik here to view.
MikroTik hardware questions • Re: RDS2216 Pics and Thoughts
Not impressed for now. The deployment of many Docker containers is painful. I bought it exclusively to deploy things like Victorialogs and Akvorado and I am hitting a wall.Not the entire fault of...
View ArticleBeginner Basics • Sanity checking on a plan for failover with two DHCP client...
Hi all, I am bad at layer 3 stuff, so apologies if I'm missing some obvious things.I've read a whole bunch of prior art on these forums, reddit, and elsewhere on doing failover on mikrotik routers....
View ArticleBeginner Basics • VLAN issue(s)
I've recently switched to Mikrotik. I was under the impression that I was quite capable, but setting up VLANs (which I've never done before) on my Mikrotik Chateau has rid me of that notion.The...
View ArticleClik here to view.
General • Re: No routes networks on RB912-LTE (2004) with EC200A modem
I emailed support yesterday, not reply yet, maybe I will hear something in the coming weeks.In the meantime I needed to get the site back online, and managed to convince someone to make a Saturday...
View ArticleGeneral • Re: PXE Boot From Mikrotik
I stumbled across a very similar issue today while trying to network boot an old LGA775 Gigabyte motherboard.I kept getting the "ERROR code:0 string:permission denied!" message, while in fact there...
View Article