General • Proper way to run zeek without port mirroring?
I'm interested in monitoring my network with zeek. I'm new at all of this, just self learning in my homelab.I'd like zeek to analyze everything going through my router. However from what I've...
View ArticleMikroTik hardware questions • NetMetal ax - help
Respected ,I tested Mikrotik netmetal ax with 2 hgo antennas.At 300m of full optical visibility, the calculation gives a signal strength of - 62.7 dB (for Tx power 29 dB and antenna gain 5.5 dB at...
View ArticleMikroTik hardware questions • Re: NetMetal ax - help
Hi, what antennas do you have?Statistics: Posted by Rox169 — Mon Mar 10, 2025 1:45 am
View ArticleGeneral • Re: Proper way to run zeek without port mirroring?
You could use mange rule:Code: /interface/bridge/settings/set use-ip-firewall=yes/ip/firewall/mangle add action=sniff-tzsp chain=forward in-interface=bridge sniff-target=10.10.10.10...
View ArticleWireless Networking • Re: HotSpot no redirect page login
same problem, till now no fix...Statistics: Posted by allan2358 — Mon Mar 10, 2025 1:49 am
View ArticleForwarding Protocols • Re: open port for dualwan help
Sorry diagram makes no sense to me, hopefully somebody with more experience with this type of setup can assist.Statistics: Posted by anav — Mon Mar 10, 2025 2:50 am
View ArticleBeginner Basics • ppsk setup?
hi, Im trying to setup ppsk but documentation seems a bit limited and i cant set it up. I want my ssid for vlan1 that is the main network and vlan30 that is the guest network they will use the same...
View ArticleClik here to view.
Containers • Containers and IPv6 addresses
This is just something I noticed, and I wonder why. Anyone know?I set up Pi-hole and unbound containers, giving them IPv4 and IPv6 addresses. Pi-hole was installed following the wiki (plus the IPv6...
View ArticleGeneral • Wireguard improvement request
Hi. I'm using the wireguard feature in CCR2004-1G-12S+2XS.Everything work great and nicely functions but some inconvenient things are presence here.After adding [WireGuard] - [Peers], I cannot use the...
View ArticleBeginner Basics • Re: ppsk setup?
Piece of advice, don't use VLAN1. If you want to use VLANs then create VLANs you need but don't use VLAN1 for anything in that case... What ROS version are you using ? I think that from 7.19 beta you...
View ArticleAnnouncements • Re: Newsletter #121 | October 2024
Hello just wanted to share I’m limited to 200-300 Mbps on Ether1 vs Ether 2-5 (switch chip) when using the port as a WAN interface. I can confirm I have the same issue on TWO separate...
View ArticleBeginner Basics • Re: invalid mtu 1492 on pppoe-out1
Hey guys, this might be of use to you:viewtopic.php?t=215423Statistics: Posted by Flannels — Mon Mar 10, 2025 7:55 am
View ArticleGeneral • Re: PPPoE client MTU get trouble
Hey guys, this might be of use to you:viewtopic.php?t=215423Statistics: Posted by Flannels — Mon Mar 10, 2025 7:56 am
View ArticleGeneral • Re: How to force "Actual MTU" on PPPoE client
I have exactly the same issue and my isp supports RFC 4638 all other routing softwares like opnsense/vyos give me 1492 but mk sticks to 1488 viewtopic.php?t=214801Hey guys, this might be of use to...
View ArticleGeneral • Re: PPPoE Compatibility Issues with vBRAS/NFV
Yes exactly i am facing this issue (pppoe isp) ONLY with mikrotik while VYOS/OPENWRT/OPNSENSE/IPFIRE happily works with their default settings giving me mtu of 1492 ,while mk defaults to 1480 and 1488...
View ArticleGeneral • Re: hEX PoE (bridge mode) is only a switch ?
As promised, here are some test results from my hAP ac². Two wired PCs are connected directly to ports ether2 and ether5 of the router and run iperf3 (in one direction).* First the bridge as...
View ArticleMikroTik hardware questions • mikrotik L009 ipsec performance?
good morning!i have a one question, now i use mikrotik hex and hap lite as a simple switch to expand ports with 100mbit and wifi 2.4, everything works fine, but I would like a little to expand my...
View ArticleGeneral • Multi level interconnection
a routeros wan 192.168.1.1 -----wireguard-------- b routeros 192.168.2.1 -----socks5-- socks5 A 192.168.4.1 socks5 b 192.168.5.1a pc1 lan 192.168.0.2a pc2 lan 192.168.0.3Match pc1 and pc2 with SOCKS5A...
View ArticleGeneral • Re: Multi level interconnection
And the question/problem is?Statistics: Posted by BartoszP — Mon Mar 10, 2025 8:31 am
View ArticleMikroTik hardware questions • Re: mikrotik L009 ipsec performance?
Make sure you stay in IPSec HW accel land.AX Lite doesnt support that:https://help.mikrotik.com/docs/spaces/R ... celerationStatistics: Posted by itimo01 — Mon Mar 10, 2025 8:32 am
View Article