Forwarding Protocols • Re: FTP cannot connect if i use the public ip
My suggestion is not to use ftp, make i vpn server on the router, and make a vpn connection into your network.It more secure and more newer and trendier.And only open up one port to the...
View ArticleBeginner Basics • Re: How to block subnet to subnet access
For a full isolation of the subnets you should have two drop forward rules:Code: /ip firewall filteradd chain=forward action=drop src-address=192.168.0.0/24 dst-address=10.0.0.0/24add chain=forward...
View ArticleRouterOS beta • Re: FEATURE REQUEST: full cone NAT
I think full cone works.I tried with stunclient from https://github.com/jselbie/stunserverAnd got Endpoint Independent NAT + Endpoint Independent FilteringOne thing I didn't see people mention, in...
View ArticleGeneral • Re: Communication between multiple subnets
Most probably yes. If not, an IP binding on the ether3 server should do the trickStatistics: Posted by TheCat12 — Fri Apr 05, 2024 7:55 pm
View ArticleAnnouncements • Re: v6.49.14 [stable] is released!
at least this problem exists:viewtopic.php?p=1064954#p1064954Statistics: Posted by pedkoschi — Fri Apr 05, 2024 8:33 pm
View ArticleBeginner Basics • Change IP addresses and gateway in wireless wire
Could someone please tell me how to change the IP address and gateway on the wireless wire so I can get updates? I tried under quick setup but it wont takeStatistics: Posted by CV123 — Fri Apr 05,...
View ArticleBeginner Basics • NetBox 5 Initial Setup
Hello all, Sorry for the newbie question (new to Mikrotik), but I'm banging my head right now. I have a new NetBox 5 that I'm trying to setup. I've powered it on and connected to the ethernet port....
View ArticleGeneral • BaseBox 2and lora interface
Hi, Is BaseBox 2 support lora card ? I've put one, but the device does not recognize pci device. There is nothing listed under device in lora and pci resources. Regards, Mariusz.Statistics: Posted by...
View ArticleRouterBOARD hardware • Re: Free up storage of CRS326 (16Mb)
Not sure why the core count is part of this discussion, but iirc, the CPU architecture of the chip is heterogenous, which the older kernel of ROS 6.x can't support. Thus only "core 0" shows up as...
View ArticleGeneral • Problem OPENVPN: Connection reset, restarting [-1]
Hi, i tried to create an OVPN server following this video:https://www.youtube.com/watch?v=LW0kbjI0XDE&t=344sBUT the client doesn't connect and I don't understand the problem;THIS IS THE LAST LOG...
View ArticleBeginner Basics • Re: AP RADIUS authorization over Wireguard site2site tunnel
If someone will be looking for this scenario...The traffic comes to the RADIUS server with IP of the router, because of masquarading which is quite obvious. The server looks at the sender IP address...
View ArticleBeginner Basics • Re: Minecraft Server, SSH, etc... protocol issue with...
Well, yeah the issue might be with the ISP, have you check it?Statistics: Posted by anovojr — Fri Apr 05, 2024 11:22 pm
View ArticleBeginner Basics • Can't use IPv6 provider prefix
My internet link comes from a modem configured by the provider, which connects to my Mikrotik on eth1, while my LAN connects on eth4.When configuring a DHCPv6 Client on eth1, I can obtain the IPv6...
View ArticleGeneral • Re: "Warning: memory not running at default frequency" -...
We have just encountered similar problems withRBD52G-5HacD2HnD and in the end there was a very simple solution, in Routerboard > Settings just change the CPU Frequency setting to...
View ArticleBeginner Basics • Re: NetBox 5 Initial Setup
Is it new, or does there maybe be any old setting in the device ?First step you should try to download winbox from this site, if you have Windows and run it, to see if you can connect to the...
View ArticleBeginner Basics • Can someone share a full working /29 config
Greetings, Looking to see a fully working config for a /29 network. Maybe even different examples if you have them. Rough network diagram attached. network_diagram.PNGStatistics: Posted by torchify —...
View ArticleRouterBOARD hardware • Re: CCR1036 Power Supply
IMHO CCR1009, 1016, 1036 and 1072 series all share the same board and all have the same problem - bad 680uFx6.3V capacitors, C1442, C143, C1613, C1617. First clue if they are failing is higher CPU...
View ArticleClik here to view.
Wireless Networking • Re: hAP ax3 wireless problem
I have received my hAP ax3, originally with a RouterOS version of 7.8. The firmware version was the same. I have since updated it with both in-built updater and netinstall, and have observed no...
View ArticleVirtualization • Re: ISSUE with PPPoE Mikrotik CHR installed in proxmox.
Hi!Check your Proxmox host " variablesCode: $> sysctl -a | grep -i XRecommended settings on Proxmox host:Code: /etc/sysctl.confnet.bridge.bridge-nf-call-ip6tables =...
View ArticleBeginner Basics • Re: Can someone share a full working /29 config
your diagram/networks It's fine as it is but really depends on what you are doing and trying to achieve, but i will do it differently because public ip is very scarce i will conserve it if i have to...
View Article