Beginner Basics • Re: Invalid TCP incoming packets with ACK,FIN,PSH, invalid...
Got the same problem. For packets incoming from LAN, I add "reject: tcp reset" just before the default invalid filter.Code: /ip firewall filteradd action=reject chain=forward connection-state=invalid...
View ArticleWireless Networking • hAP AX2 - broken wifi (no SSID can be found)
I have no clue on how to fixed this problem. Its been a while and upgrading the FW or reset using the script did not help. Basically the WIFI is broken and no way out. Current setup routeros 7.14.1...
View ArticleWireless Networking • Re: hAP AX2 - broken wifi (no SSID can be found)
Can you share your configuration ? Did you try to downgrade ROS to version your WiFi worked ?Statistics: Posted by gigabyte091 — Mon Mar 18, 2024 6:59 am
View ArticleGeneral • Re: Very bad reliability Mikrotik Products and ROS
Not only software bug, my CCR1036 got 4 times PSU failure since 2018, average 1.5 year with one PSU failed.Bad cheesy cheap hardware design, my LED display fall into the case and need me to glue it to...
View ArticleClik here to view.
General • Re: lo-Interface loopback
Standard loopback interface.It has always been there but was hidden in the past.Recent versions of ROS made it visible.Don't worry too much about it and just let it be Statistics: Posted by holvoetn —...
View ArticleBeginner Basics • Re: mikrotik vlan mgmt, access ptp connect
What your missing is that each smart device should get an IP from a management vlan.Data vlans 17 and 89 are carried forward to each smart device as well.Assuming that the ROUTER has its own internal...
View ArticleWireless Networking • CAPS MAN WIFI - Devices ROS6 and ROS7
Hey everyone,I'm seeking some guidance on integrating a new L009UiGS-RM WiFi device into my current setup. Currently, I'm running CAPsMAN on 1100AHx2 hardware with Package and firmware version...
View ArticleWireless Networking • Re: CAPS MAN WIFI - Devices ROS6 and ROS7
You can run both versions of capsman on the same device as of ROS7.13.The only caveat is that if that controller device also has a local radio, it will loose that capability since you need to have...
View ArticleScripting • DDNS Cloudflare script
Hello everyone,I would like to preface by saying that I am not a programmer and I need help solving the following issue. I have written the following script for RouterOS that updates the IP in a given...
View ArticleGeneral • Re: v7.15beta broke backup file naming
I'd rather ask "which characters are safe to use?" ... and the answer would be: the same as the last 50 years: US ASCII alphabet (a-z and A-Z), roman numerals (0-9), underscore (_), dash (-) ... and...
View ArticleBeginner Basics • Re: Attempting to evolve from caveman's failover
Recursive has nothing to do with the issue I had, at least one route should have not been USHI.And at the time, before trying with VRF and with the other method using proxy ARP, I did try the "plain"...
View ArticleGeneral • Re: [SHARE] IPv6 gigabit solution for now
I tried assign an IPv6 to a bridge got 800Mbps for few hours then drop to 600MbpsComments are welcomeI suspect that is related to the architecture.. Take a look at the block-diagram and how the ports...
View ArticleAnnouncements • Re: v7.14.1 [stable] is released!
...updated two hap ac^3 from 7.13.1 to 7.14.1....both devices are running wifi-qcom-ac, vlans for ssids in bridge filtering mode and booting in CAP modeThe bridge/vlan config got messed up completely...
View ArticleGeneral • MultiWAN + LAN through vlans
Hello!at first - my English is not enough for long explanations, but I hope You understand me )second - special thanks to @pcunite for these posts Using RouterOS to VLAN your network and MultiWAN with...
View ArticleClik here to view.
Beginner Basics • Re: 2WAN as Failover and Setup Wireguard KEY as Client
Sorry my bad on the TYPO, WG1 is the correct entry on the routing rule to match the routing-table defined.Good then put IP addresss on your router for wireguard1 asadd address=192.168.32.20/24...
View ArticleRouterBOARD hardware • Re: CCR1036 temperature "issue" cause reboot.
Got a CCR1009 here with these symptoms (temperature reboot, though unit is cold). Replaced bulged caps C1442 and C1443 (680µF/10V) with Panasonic FR and it worked again. System Health showed voltage...
View ArticleClik here to view.
Beginner Basics • Re: IOT devices over wireless - DHCP assigns and deassigned
having the same issue.IoT devices are disconnecting intermittently. Wifi signal is pretty strong.Running an RB5009 on 7.14 and two cap AC`s with Capsman in forwarding mode.Bildschirmfoto 2024-03-18 um...
View ArticleBeginner Basics • IPTV settings
Hello,I have very simple config. ether1 is WAN port and here comes internet and tv from ISP. Other ports combined into on bridge and on other2 sits TV (it allows media casting like youtube and music)...
View ArticleGeneral • Re: 7.14 and SMB on RB5009
This is so weird. Running 14.1 - had add comment in SMB settings - then it started to work. Mikrotik AX3.Statistics: Posted by foegra — Mon Mar 18, 2024 11:23 pm
View ArticleBeginner Basics • NFS Client Help
Everyone seems excited that ROSE storage will allow you to use your MikroTik as a very basic NAS. This is nice, but I want to use it the other way. Many new models are coming out without USB and I'd...
View Article