Clik here to view.
General • Re: sfp info not shown/eeprom-checksum: bad
Does a good hardware reset Thank you! Did helped!Statistics: Posted by smotrov — Sun Dec 03, 2023 9:04 pm
View ArticleAnnouncements • Re: v7.12.1 [stable] is released! server x64bits L2MTU issue
Hi guys i am having issue in changing the L2MTU on V7.12.1 X64 Running 2 cards Intel XDA-520 and Mellanox Card dual 40Gbps all nics show up the same MTU 1500 and L2MTU 0 i cannot change the L2MTU.. is...
View ArticleRouterBOARD hardware • Re: Problems with X520-DA2
Hi guys it looks like i have the same problem, all the Fiber nics 10gbps, 40gbps inserted on the Mikrotik RoS 7.12.1 stable... have mtu 0..so how raising MTU from 1500 to 1598 for example will...
View ArticleBeginner Basics • Re: OVPN SITE TO SITE - route issue
Hi.Routes are correct.I don't have experience with OVPN, I am using Wireguard for Site2Site, so can't tell nothing about this kind of configuration. But it looks like an issue with firewall rules for...
View ArticleContainers • Re: Containers broken after restore from backup
What version of RouterOS and also what container?7.12technitium/dns-server:latest is the first container in the listI'm going to save my container settings and then nuke them and retry. It may be that...
View ArticleBeginner Basics • Re: CPE and issue with resceving an IP
Ok, so I have upgraded my main capsman managaer to 7.12.1 and now I'm back and my little bypass does not seem to work anymore, anyone who knows how to fix this?Statistics: Posted by pomah — Sun Dec...
View ArticleBeginner Basics • WiFi with WPA2-PSK + WPA2-EAP certificate authentication
Hello guys!I got a WiFi dedicated for company smartphones, it uses WPA2-PSK and I would like to get it more secure than just typing password. My idea at this point is to generate a "global"...
View ArticleClik here to view.
Beginner Basics • Best approach to dual purpose device - wifi ap / lte travel...
O' Wise Ones!Here I come in peace, seeking your guidance and bringing the story of two devices that can't rest without one another. How do I keep them together?accidentally posted draft, need few...
View ArticleClik here to view.
Wireless Networking • Wireless connection supporting ISP Fiber speed
My RB3011 wan is connected to ISP vdsl router via a pair of SXT5ac (claiming 650Mbps-80MHz/2S/SGI radio channel), more than enough for actual 20 Mbps internet speed I'm planning to switch to a 1Gbps...
View ArticleBeginner Basics • Re: Backup router with DHCP server
Hi there.You should check out VRRP:1) It should be a "slave" interfaces for all vlans which you wants to "secure" when Master is unreachable,2) You should use scripts for enable/disable interface...
View ArticleWireless Networking • Re: WiFi for sports hall?
I am asking if it would be possible in any way. The sports hall is indoor, with up to 10k people and this should be an event where people should stay at the playground too. Possible mount options are...
View ArticleGeneral • Re: "NAT forward to gateway"
If you have a route to 10.20.7.0/24 (or what the actual mask is) on router A, NAT at router B should normally not be necessary. So there must be some additional issue which I cannot guess. Hence post...
View ArticleGeneral • Re: Wireguard Road Warrior to L2 LAN
If you only want the roaming client to be able to connect to devices in 192.168.20.0/24 and not vice versa (i.e. you don't need that those devices could actively initiate connections to the roaming...
View ArticleBeginner Basics • Need help with weird problem. (Device periodically lose...
Here is my setup:Telus 3Gbps Fiber-> Nokia ONT -> CCR2004-16G-2S+ -> QNAP M408-4C(switch connected via SFP+) No Vlan or QoS is used in any device.Under the switch, I have all my wired...
View ArticleGeneral • Force ipv4 to use for some sites if it have ipv4 and ipv6 address...
Hello.How to configure mikrotik so it will force use of ipv4 for some sites? I have configured sit tunnel to tunnel broker, but some sites not open or blocked in ipv6, so i want to use ipv4 for them...
View ArticleGeneral • Port forward problem
I have a Mikrotik RB750Gr3 router with RouterOS 7.12.1. Ether 1 is connected to the internet on a static IP. Ether 2 plugs into the protected side of DCB box 1 running as a server. The DCB box...
View ArticleClik here to view.
SwOS • Host learned on Trunk port instead of physical one
Hi forum,I've been having this issue for quite a while but never got around to fully fix it as I have a work around that kept things "working", but now I'm trying to look on how to sort this out.I...
View ArticleGeneral • Re: NordVPN too Slow after configuration
Use wireguard instead!!!Statistics: Posted by anav — Mon Dec 04, 2023 2:20 am
View ArticleGeneral • Re: Force ipv4 to use for some sites if it have ipv4 and ipv6...
If client devices resolve both IPv4 and IPv6 addresses for a target site they will use IPv6 in preference to IPv4 to connect. AFAIK Android and iOS implement 'Happy Eyeballs' for fast fallback to...
View ArticleGeneral • Re: Wireguard tunnel - speed problem
Well the speeds all look pretty good, from one wireguard endpoint to the other endpoint, via wireguard.(This is what the graphs are isn't it?)So perhaps it is the Lan interfaces that are causing the...
View Article