Scripting • Script - Zabbix - Getting values from ping and loss inside Mikrotik
Well, work is done. This use Zabbix to get a value from ping and loss inside Mikrotik.Template for Zabbix 6.0OBS: Only run with SNMP read/write access. Please use SNMP version 3!You need to create the...
View ArticleBeginner Basics • Re: LTE backup
You can add a masquerade or srcnat pointing to the LTE interface.If the distance is higher the route won't be active so there won't be traffic out of that port.The issue is only that the setup (as you...
View ArticleBeginner Basics • Re: wireguard connection restricted to a single internal IP
Hello Anav,Tis very much for the firewall / NAT configuration. I did set up the MK as you informed and I can access my Synology server using WG tunnel.I have another question and would like to know if...
View ArticleWireless Networking • Re: Can't coonnect to Cap AC
Found the problem but don't know why.I could not connect via Winbox (i have the v3.40), but tried via my work laptop (v3.35) and could connect.. i tried then to copy winbox to my PC but did not work.....
View ArticleGeneral • No traffic across IPSEC tunnel to AWS
Hi, I've got functional tunnels and BGP peering ok. Prefixes are as expected on both sides, so I'm thinking I have an iptables problem. I've played with some of what I've seen on other posts in NAT...
View ArticleRouterOS beta • Re: v7 inter VRF route leak doesn't work for local IPs
@mrzthis is the plan for v7.15?Code: /ip routeadd dst-address=10.11.0.0/24 gateway=vrfTest1@vrfTest1 routing-table=vrfTest2add dst-address=10.12.0.0/24 gateway=vrfTest2@vrfTest2...
View ArticleRouterBOARD hardware • map2nd mAP serial port
I see RX, TX, 3.3V and ground pads on the circuit board of the map2nd. Is this a serial port? Can I use this to talk to a serial device remotely?Thanks!Statistics: Posted by rilliam — Mon Mar 11, 2024...
View ArticleWireless Networking • Re: FQ_codel on mikrotik wifi?
Is the following the best way to test this on new ax devices? - run fq_codel on wireless interface- use two local machines on wifi for flent server and clientStatistics: Posted by mke — Mon Mar 11,...
View ArticleGeneral • Re: No traffic across IPSEC tunnel to AWS
Finally got ICMP working, but I'm not wild about this solution. Apparently if I add another policy for the src and dst network prefixes, it works. I was hoping that wasn't necessary since I'm trying...
View ArticleGeneral • slow speed wifi download while make a bridge
After conducting countless tests, I have obtained the following accurate and repeatable results. I seek the assistance of experts to determine whether the issue lies with me or with ROS:My ESXi setup...
View ArticleGeneral • LTE eSIM (embedded-SIM) feature
Hello Everyone,I was wondering if Mikrotik have plans to introduce eSIM (embedded-SIM) in LTE 5G devices ?Statistics: Posted by volga629 — Mon Mar 11, 2024 3:29 am
View ArticleBeginner Basics • Re: Need help with L3 VLAN
As long as the port using the vlan is not on the bridge its a viable path.If you have the vlan on the bridge then you should use all vlans and the bridge does no DHCP etc...Do not use VLAN1 for...
View ArticleContainers • Re: AdGuard Home container fails to connect to TLS servers
Upon closer inspection, I traced the packets back to my main firewall IPTables.There was a chain blocking any packet on port 853 that was not destined for the main DNS host, which is also an ADH...
View ArticleGeneral • Re: slow speed wifi download while make a bridge
please find the attached pictures.Downloading from local network via wifi is too slow while upload speed is satisfied.I also noticed data downloaded from public network (WAN-CU to AP) will go through...
View ArticleGeneral • Re: Simple Queues with PCQ and Burst
Perhaps, anyone?Statistics: Posted by defconfonly — Mon Mar 11, 2024 5:35 am
View ArticleRouterBOARD hardware • RB2011IsAS-RM - eth10 dead?
I have an RB2011IsAS-RM to play with. I was hoping to set eth10 as my management access port, but I have a feeling it's dead.Setting an IP address, DHCP etc works fine, but I can't connect to the...
View ArticleBeginner Basics • Re: How to configure and debug mikrotik CRS326 24 switch to...
You do realise that CRS326 is a switch, not a router ? You can expect max about 250-270 Mbps bandwidth... You should export your configuration and post it here.Statistics: Posted by gigabyte091 — Mon...
View ArticleGeneral • Re: LTE eSIM (embedded-SIM) feature
It's already in the menu structure but not functional yet.So yes, it should be coming.Statistics: Posted by holvoetn — Mon Mar 11, 2024 7:12 am
View ArticleRouterBOARD hardware • Re: map2nd mAP serial port
If anything, this is TTL-level serial. You'd need something like MAX232 to convert levels to RS232 levels (which is 5V), without it you'd fry the board components.Next problem is that this serial...
View ArticleClik here to view.
RouterBOARD hardware • Re: Many Mikrotik boxes ? Just recycle !
Cats too! Statistics: Posted by MickeyT — Mon Mar 11, 2024 8:12 am
View Article